Arm and shoulder exoskeleton: comparison and prices 2026
Hapo UP and FRONT, Hilti EXO-S, Ottobock Paexo Shoulder, Levitate Airframe, Festool ExoActive: six arm and shoulder exoskeletons compared on weight, assistance and price, with the trades concerned and what studies say.
Arm exoskeleton: what is it for, and who needs one?
Screwing a board to the ceiling, sanding a wall above your head, installing cable trays: when your arms stay raised for hours each day, your shoulders take the strain. An arm and shoulder exoskeleton takes over part of the weight of the arms and transfers it to the hips or pelvis, using springs, cables or a motor. It does not help you carry heavier loads: it reduces the effort on the shoulders while working with your arms in the air.
The stakes are real. According to the French occupational safety institute INRS, musculoskeletal disorders account for more than 80% of recognised occupational diseases in France. Shoulder exoskeletons target one of their causes precisely: prolonged arm elevation.
This comparison brings six passive and active models together in a single table: weight, stated assistance and list price where one exists. Prices are those found in October 2026 on manufacturer and distributor websites. They are professional prices, often excluding VAT, and change with discounts and volumes: check them before ordering. For an overview of the other families, start with our exoskeleton guide.
Passive or active: two families of shoulder exoskeletons
Passive models: springs and cables
Most shoulder exoskeletons are passive. Leaf springs, gas springs or cables tension as the arms come down and give that energy back as they rise. No battery, no electronics: they work all day without charging and stay light. Their limit: assistance is set by the spring setting, and it can get in the way when you lower your arms to pick up a tool.
Active models: motor and battery
An active model uses a battery-powered motor or compressor. Assistance can be adjusted to the task, and the system can lock or release depending on the movement. In return, the device is much heavier and the batteries need charging. For the difference in detail, see our question active, passive or textile exoskeleton: what are the differences?
Arm and shoulder exoskeletons compared in 2026
| Model | Type | Target arm position | Stated weight | Stated assistance | List price |
|---|---|---|---|---|---|
| Hapo UP | Passive | Above the head | 1.87 kg | Not quantified by the manufacturer | €3,500 excl. VAT |
| Hapo FRONT | Passive | In front, arms extended | 1.3 kg | Up to 2 kg or 3 kg per arm depending on version | €1,900 excl. VAT |
| Hilti EXO-S | Passive | Above the shoulders | 2.4 kg | Up to 60% less shoulder strain, depending on the task | From €2,119 excl. VAT |
| Ottobock Paexo Shoulder | Passive | Above the head | 1.9 kg | Not published | On quote |
| Levitate Airframe | Passive | Raised arms, repetitive motions | Not published | Up to 80% less exertion, according to the manufacturer | On quote |
| Festool ExoActive | Active (battery) | Above the head | 7 kg | 5 kg (50 N) per arm | On quote |
Table sources: the manufacturer pages for the Hapo UP, the Hapo FRONT and the Hilti EXO-S (in French), the Ottobock press release for the Paexo Shoulder, the Airframe listing published in the US industrial press and the Festool ExoActive data sheet on Batiproduits (in French). "On quote" means the manufacturer displays no list price.
Two things to keep in mind when reading it:
- Assistance figures cannot be compared directly. Hapo and Festool give a weight supported per arm, Hilti and Levitate a percentage of effort reduction measured in their own tests. A percentage stated by a brand is not an independent measurement.
- Prices excluding VAT are for professionals. A company recovers VAT; an individual or a tradesperson not registered for VAT pays the price including tax.
The six models in detail
Hapo UP: the overhead specialist
The Hapo UP is designed by French manufacturer Hapo for tasks with arms held up and for lifting light loads between 60° and 180° of elevation, according to its official page. It weighs 1.87 kg and works with leaf springs. Hapo mentions the mechanic under a vehicle lift, the painter sanding a ceiling and the employee stocking products on high racks. It is the most expensive of the passive models with a list price: €3,500 excluding VAT. See the Hapo UP product page.
Hapo FRONT: for arms held in front of you
The Hapo FRONT targets another posture: arms extended in front of you, at chest or shoulder height. Its page offers two versions, 4 kg and 6 kg, meaning up to 2 kg or 3 kg per arm depending on the version. At 1.3 kg, it is the lightest in this comparison, and the cheapest at €1,900 excluding VAT. Hapo mentions surgeons during long operations, precision operators in industry and farmers during milking. See the Hapo FRONT product page and our guide to the Hapo range.
Hilti EXO-S: the construction site benchmark
Hilti's EXO-S is a passive exoskeleton that transfers the load from the shoulders to the hips. According to Hilti France, it weighs 2.4 kg, adjusts from XS to XXL without tools and fits biceps up to 40 cm around; a large version exists beyond that. Hilti states up to 60% less strain on the shoulders depending on the task, and offers an optional neck support. The displayed price starts at €2,119 excluding VAT, with each company's actual price shown after login. Hilti mentions drywall installation, sanding walls and ceilings, and ceiling installations: pipework, sprinklers, ventilation ducts, cable trays.
Ottobock Paexo Shoulder: light and proven in industry
Germany's Ottobock, known for its prostheses, developed the Paexo Shoulder for overhead work. According to an Ottobock press release, it weighs 1.9 kg, is worn like a backpack and transfers the weight of the raised arms to the hips through a cable system, with no battery. The company notably supplied it to painting crews at a timber-frame house builder. Ottobock does not publish a price: you need a quote, from the brand or a distributor.
Levitate Airframe: the American pioneer
The Airframe from US company Levitate is also worn like a backpack, with arm rests and a system of pulleys and springs, with no power supply. According to the listing published in the industrial press, the manufacturer claims up to 80% less exertion. That is the brand's figure, and we found neither an up-to-date official page nor a list price. Its distribution in France is not established: it is for companies ready to import and request a quote.
Festool ExoActive: the drywaller's active exoskeleton
The Festool ExoActive is the only active model in this comparison. According to its data sheet, it provides 5 kg (50 N) of assistance per arm, runs on an 18 V 4 Ah battery and lasts 1.5 to 5 hours depending on use. It offers three preset movement ranges and two modes, one that holds the arms in position and one that follows them. The downside: 7 kg on your back, and 13.3 kg with the transport accessories. It mainly targets drywall installation on walls and ceilings. The price is available on quote.
How much does an arm exoskeleton cost?
In this comparison, list prices range from €1,900 excluding VAT for the Hapo FRONT to €3,500 excluding VAT for the Hapo UP. This matches the INRS FAQ (in French), which says most non-robotic models do not exceed €5,000, while robotic technologies can reach almost €50,000.
The purchase price is only part of the budget. Also plan for:
- a trial phase at the real workstation, ideally with several models loaned or rented: see our question on renting an exoskeleton;
- user training, which the INRS recommends as a familiarisation programme;
- maintenance: fabric parts and pads wear out, especially on construction sites;
- sizes: one model does not fit every build, which may mean buying several units.
On funding, a French company can sometimes get support when the purchase is part of a musculoskeletal disorder prevention plan: see our question on financial aid for companies and the one on who pays for an exoskeleton at work. For prices of other families, read our article on exoskeleton prices.
Which trades work with arms raised?
A shoulder exoskeleton makes sense when the arms stay above shoulder height for long periods or repeatedly. The trades mentioned by manufacturers and studies fall into these groups:
- Construction, finishing trades: drywallers and plasterers, ceiling painters, electricians, plumbers and heating engineers installing networks on ceilings, ventilation and sprinkler installers. See our article on exoskeletons in construction.
- Industry and maintenance: mechanics under a vehicle lift, fitters on automotive and aerospace lines, precision operators.
- Logistics and retail: employees stocking products on high racks, shelf restocking in stores.
- Agriculture: farmers during milking, pruning in orchards or vineyards. See our article on exoskeletons in agriculture and viticulture.
- Healthcare: surgeons during long operations with arms extended.
If it is mainly the neck that hurts, when the head stays tilted up, a cervical model can complement or replace the shoulder exoskeleton: see our question on head-up work.
What studies say
Shoulder exoskeletons are among the most studied. A literature review published in 2022 in Frontiers in Robotics and AI included 35 studies covering 18 different exoskeletons. Of these, 16 studies show reduced activity in the deltoid and trapezius muscles with the exoskeleton. The authors note, however, that effects measured in the field are less pronounced than in the lab, probably because a real workstation mixes overhead work with secondary tasks.
The INRS adds other nuances. An exoskeleton is not personal protective equipment, and no scientific evidence shows to date that it reduces musculoskeletal disorders. It can also create new strains: with an arm-assist exoskeleton of about 9 kg, during a box-handling task, cardiac cost rose by about 15% on average. Details are in our question on cardiac strain. Finally, the INRS points out that the exoskeleton must be included in the company's risk assessment.
This is not medical advice: if your shoulder hurts, talk to your occupational physician before choosing a device.
How to choose an arm and shoulder exoskeleton
- Identify the main arm position. Above the head: Hapo UP, Hilti EXO-S, Paexo Shoulder or ExoActive. In front, at chest height: Hapo FRONT.
- Estimate the weight of the tools. A light screwdriver does not need the same assistance as a hammer drill or a ceiling sander. The Hapo FRONT is chosen precisely according to this load.
- Count the movements below shoulder height. If the worker often bends down to pick up materials, a spring that is too strong gets in the way. A model that can be disengaged, or an active one, may then suit better.
- Check compatibility with other equipment: fall-arrest harness, tool belt, helmet, workwear.
- Test at the real workstation, over several days. How it feels in the first few minutes says nothing about the end of the day. See also our question can you wear an exoskeleton all day?
Our verdict
For a controlled budget and arms held in front, the Hapo FRONT is the most accessible entry point, with a list price and the lowest weight in this comparison. For overhead work, the Hilti EXO-S and the Hapo UP share the field: the first is widespread on construction sites and comes in several sizes, the second is lighter. The Paexo Shoulder is a solid alternative, but has no list price. The Festool ExoActive is for workstations where assistance needs to vary during the day and where its 7 kg is acceptable. As for the Airframe, its availability in France remains to be checked.
In every case, the exoskeleton comes after workstation design: a platform at the right height or a tool with a telescopic handle sometimes removes the problem at the source.
Frequently asked questions
How much does an arm exoskeleton cost?
Among models with a list price, expect €1,900 excluding VAT for the Hapo FRONT up to €3,500 excluding VAT for the Hapo UP; the Hilti EXO-S starts at €2,119 excluding VAT. Ottobock, Levitate and Festool sell on quote.
Which exoskeleton for working with arms raised?
For arms above the head, look at the Hapo UP, the Hilti EXO-S or the Paexo Shoulder for passive models, or the Festool ExoActive for an active one. For arms extended in front, the Hapo FRONT is better suited. See also our question arm and shoulder exoskeleton: which model for overhead work?
What is the lightest shoulder exoskeleton?
According to manufacturer pages, the Hapo FRONT at 1.3 kg, ahead of the Hapo UP and the Paexo Shoulder. The powered Festool ExoActive weighs 7 kg.
Is a passive exoskeleton enough?
For most workstations, yes: passive models cover overhead work with no battery or charging. An active model makes sense when assistance needs to change with the day's tasks.
Can an individual buy a shoulder exoskeleton?
Yes, nothing prevents it, but these models are designed and sold for professionals. Displayed prices often exclude VAT, and several brands only sell on quote.
Further reading
To choose by trade, read our exoskeleton guide by job, then browse the Hapo selection and our 2026 comparison across all families.
Related questions
-
Overhead work exoskeleton: which one for working with your arms raised?
For work with your arms above your head (ceilings, ducts, painting), choose a shoulder exoskeleton designed for elevation, such as the Hapo UP or the Hilti EXO-S. For arms held in front of you, the Hapo FRONT fits better. These passive models need no battery and reduce shoulder effort, but should be tried at the real workstation.
Read the answer →